Philips Clock Radio AJL308 78 User Manual

Clock Radio  
AJL308  
Register your product and get support at  
UserManual
 
Mexico  
Es necesario que lea cuidadosamente su instructivo de manejo.  
Descripción:  
Modelo:  
Radio reloj  
AJL308/55  
Alimentación:  
Consumo:  
110–127/220–240V; ~50–60 Hz  
9 W  
Importador:  
Domicilio:  
Philips Mexicana, S.A. de C.V.  
Av. La palma No. 6  
Col. San Fernando la Herradura, Huixquilucan  
Localidad y Telefono:  
Edo. de México C.P. 52784  
Tel. 52 69 90 00  
Exportador:  
País de Origen:  
Nº de Serie:  
Philips Electronics Hong Kong Ltd.  
China  
______________________________________  
LEA CUIDADOSAMENTE ESTE INSTRUCTIVO  
ANTES DE USAR SU APARATO.  
AVISO IMPORTANTE  
Philips Mexicana, S.A. de C.V. no se hace responsable por daños o desperfectos causados por:  
– Maltrato, descuido o mal uso, presencia de insectos o roedores (cucarachas, ratones etc.).  
– Cuando el aparato no haya sido operarado de acuerdo con el  
instructivo del uso, fuera de los valores nominales y tolerancias de las tensiones (voltaje), frecuencia  
(ciclaje) de alimentación  
eléctrica y las características que deben reunir las instalaciones auxiliares.  
– Por fenómenos naturales tales como: temblores, inundaciones, incendios, descargas eléctricas, rayos  
etc. o delitos causados por terceros (choques asaltos, riñas, etc.).  
 
 
English  
Controls  
Congratulations on your purchase and  
4 PHOTO/VIDEO  
– switches between photo and video modes  
5 MUSIC  
– switches to music mode  
6 SLEEP  
welcome to Philips!  
To fully benifit from the support that  
Philips offers, register your product at  
– sets, activates or deactivates sleep function  
7 ALARM 1/ALARM 2  
Supplied accessory  
– sets, activates or deactivates alarm  
– 1 X certified power adapter  
(Input: 100-240V ~50/60Hz 0.3A~0.4A,  
Output: 9V 1A)  
8 REPEAT ALARM/BRIGHTNESS  
CONTROL  
– repeats alarm at 9-minute interval  
– adjusts brightness of LCD screen  
9 VOLUME  
Controls (see 1 )  
– adjusts volume level  
1 MENU  
0 DC IN  
– switches to menu setting  
2 CLOCK  
– switches to clock mode  
socket for DC 9V adaptor  
! SD/MMC slot  
– connects to SD or MMC card  
3 TUNER  
@ USB port  
– switches to tuner mode  
– connects to USB device  
# Pigtail FM antenna to improve reception.  
$ OK, 3,4,2,1  
Mode  
Clock  
Tuner  
Music  
Photo  
Video  
Button  
**Enlarge a pic-  
ture in zoom mode  
Turn on or off  
radio  
Start or pause Display a picture Start or pause  
playback in a full screen playback  
OK  
-Select previ-  
ous photo  
-Navigate in  
zoom mode  
-Select a radio  
station  
-Select a preset  
number in  
program mode  
-Select Repeat -Rotate a pic-  
-Switch between  
o
One/All or  
ture 90 clock- 16:9 and 4:3  
shuffle mode wise  
screen ratio  
*- Selects audio  
language  
3
-Cancel play -Navigate in  
mode  
thumbnail pic-  
tures  
- Select next  
photo  
-Navigate in  
zoom mode  
-Select a radio  
station  
-Select a preset  
number in  
program mode  
-Select Repeat -Rotate a pic-  
-Select Repeat  
One/All mode  
-Cancel play  
mode  
o
One/All or  
ture 90 anti  
shuffle mode clockwise  
-Cancel play -Navigate in  
4
mode  
thumbnail pic- *- Selects  
tures  
subtitle language  
- Select next  
photo  
-Fine tune to a  
station  
-Select next  
music file  
-Select next  
photo  
-Select next  
video file  
-Navigate in  
zoom mode  
*-Tune to a radio *-Fast forward -Navigate in  
*-Fast forward  
playback  
2
1
station  
playback  
thumbnail pic-  
tures  
-Select previ-  
ous photo  
-Navigate in  
zoom mode  
-Fine tune to a  
station  
-Select previ- -Select previous -Select previous  
ous music file photo  
video file  
*-Fast reverse  
playback  
*-Tune to a radio *-Fast reverse -Navigate in  
station  
playback  
thumbnail pic-  
tures  
* = press and hold  
** = in clock mode, press and hold CLOCK button to enter zoom mode  
 
Alarm  
Power supply/Basic operation  
To change time format  
In the Clock menu, press 3 4 to select the  
value of “12/24 Hour Format”.  
Power supply  
Connect the supplied power adapter to the  
set's DC 9V socket and to the power socket.  
1
2
1
Press 1 2 to toggle between 12H and 24H.  
Helpful hints:  
To avoid damage to the set, use only the  
adapter supplied!  
Note:  
When the set is disconnected from the power  
outlet for about 5 minutes, you need to reset the  
time and date.  
The type plate is located on the bottom  
of the set.  
Setting and activating alarm  
You can set two different alarm times.  
Setting OSD (On Screen  
Display) language  
Press MENU.  
1
2
Press CLOCK.  
Press and hold ALARM 1 or ALARM 2.  
The hour digits flash.  
1
The menu appears.  
2
3
4
5
Press 1 2 to highlight “General”.  
Press 4 to highlight “Language”.  
Press 1 2 to select desired language.  
After finishing the setting, press CLOCK,  
TUNER, PHOTO/VIDEO or MUSIC to  
exit the setup menu.  
3
4
Press or hold down 3 4 to set hour.  
Press ALARM 1 or ALARM 2 to confirm.  
The minute digits flash.  
Press or hold down 3 4 to set minute.  
Press ALARM 1 or ALARM 2 to confirm.  
Press again ALARM 1 or ALARM 2 to  
activate alarm setting.  
5
6
7
When alarm is activated,  
At the set alarm time,  
is displayed.  
Setting time and date  
the alarm will sound and its volume will  
increase gradually.  
Selecting alarm mode  
1
Press MENU.  
The menu appears.  
2
3
4
Use 1 2 to highlight “Clock”.  
Press 34 to select “Alarm Music”.  
Press 1 2 to select specific music you like.  
Alarm will go off with the music you select.  
1
2
3
Press CLOCK.  
Use MENU.  
Switching off the alarm  
There are three ways of switching off the  
alarm. Unless you choose to cancel the alarm  
completely, the DAILY ALARM RESET option  
will be automatically kept activated from the  
time your alarm first goes off.  
Use 3 4 1 2 to select a field of “Time  
Set” and “Date (Year-Month-Day)”.  
Press OK to confirm.  
Press or hold down 3 4 to set the values.  
Press OK to confirm.  
Repeat Steps 3-6 to set other values of “Time  
Set and “Date (Year-Month-Day)”.  
After finishing the setting, press CLOCK,  
TUNER, PHOTO/VIDEO or MUSIC to  
exit the setup menu.  
4
5
6
7
Daily alarm reset  
If you want the alarm to be stopped  
immediately but also wish to repeat the alarm  
call at the same time for the following day:  
8
 
Digital tuner  
1
During the alarm call, press any button except  
REPEAT ALARM / BRIGHTNESS  
Turning on/off radio  
To turn off radio, press OK.To turn on radio,  
press OK again.  
.
CONTROL  
is displayed.  
To improve reception:  
FM: Extend and adjust the pigtail for optimum  
reception.  
Repeat alarm  
This will repeat your alarm call at 9-minute  
intervals.  
1
1
During the alarm call, press  
REPEAT ALARM / BRIGHTNESS  
Programming radio stations  
You can store up to a total of 20 FM radio  
stations in the memory, manually or automati-  
cally (Auto store).  
.
CONTROL  
flashes.  
Switching off the alarm completely  
Press repeatedly ALARM 1 or ALARM 2  
Manual programming  
Tune to your desired station (See “Tuning to  
radio station”).  
Press and hold TUNER for about 2 seconds,  
then release.  
Preset number will flash.  
Press 34 once or more to allocate a  
number from 1 to 20.  
1
2
until  
is changed to  
.
When alarm is deactivated,  
is dispalyed.  
Helpful hints:  
During alarm call, if no button is pressed, alarm  
call will last 30 minutes.  
3
Preset number will flash.  
4
5
Press TUNER again to confirm.  
Repeat steps 1-4 to store other stations.  
Tuner  
Note:  
You can erase a preset station by storing  
another frequency in its place.  
Auto store  
Autostore automatically starts programming  
radio stations from preset 1. Any previous  
presets e.g. manually programmed will be  
erased.  
1
InTUNER mode, press MENU to display  
tuner menu.  
2
3
Press 4 to select “Tuner Auto Program”.  
Press OK.  
Available stations are programmed (FM).  
After all stations are stored, the first auto-  
store preset station will then automatically  
play.  
Tuning to radio station  
1
2
Press TUNER to switch on radio (FM only).  
Press and hold 1 2 for about 2 seconds, then  
release.  
The radio automatically tunes to a station  
of sufficient reception.  
Repeat step 2 if necessary until you find the  
desired station.  
To tune to a weak station, press 1 2 briefly  
and repeatedly until you have found optimal  
reception.  
To listen to a preset or autostore  
station  
Press 34 once or more until the desired  
preset station is displayed.  
3
 
USB/Memory card(SD/MMC)  
The slideshow of the stored pictures will  
Using USB device/memory  
card (SD/MMC)  
start from the selected picture.  
o
Press 34 to rotate the picture 90 clock-  
Connect a USB device, or a memory card  
(SD or MMC card) to AJL308, you can enjoy  
audio, picture and video files stored on the  
USB device or memory card through the  
speakers and LCD screen of AJL308.  
wise or anti clockwise.  
Press 1 2 to display previous/next photo.  
To change slideshow interval, see “Using  
setup menu options”  
To view photo in clock mode  
Press OK to access thumbnail, then press 3  
4 1 2 to select desired photo, then press  
OK to confirm.  
Or, direclty press 3(1) /4(2) display  
previous/next photo.  
To enlarge the displayed photo (zoom  
mode), press and hold CLOCK for around  
2 seconds, then press OK repeatedly to  
enlarge picture or resume to normal size, and  
you may use 3 4 1 2 to pan the enlarged  
picture through.To exit zoom mode, press  
CLOCK again.  
Listening to music  
1
1
2
Plug a compatible USB device or a memory  
card (SD or MMC) to USB port, or memory  
card slot.  
The folder(s) indicating the inserted device  
appears.  
Press 3 4 to select the folder of USB  
device (if present) or memory card (if pres-  
ent).  
Press OK to open the folder.  
The set will auto switch to clock mode.  
Press MUSIC to switch to music mode.  
All the stored music files are listed in the  
menu.  
Press 34 to select a file.  
Press OK to play.  
3
4
5
6
To pause, press OK.To resume, press OK  
again.  
Before zoom  
After zoom  
To select next/previous file, press 1 2.  
To fast forward/reverse, press and hold  
2 or 1 until  
6
or  
5
appears on the  
lower- left corner of the screen, then press  
briefly and repeatedly to select 5 different  
playback speeds.To return to normal play-  
back, press 2 or 1 until displayed  
is change to 2.  
6
or  
5
To repeat One,All or Shuffle, press once  
or more 3\4.To cancel play mode, press  
3\4 until “Offis display.  
Viewing photo  
1
2
Repeat steps 1 to 3 in “Listening to music”.  
Press PHOTO/VIDEO to switch to photo  
mode.  
The pictures stored on the USB device or  
memory card will be displayed in  
thumbnail.  
3
To display a picture in full screen, press 3 4  
1 2 to select a thumbnail, then press OK.  
 
USB/Memory card(SD/MMC)  
To select display picture format  
Compatible memory card  
– SD card  
– MMC card  
You may change still picture display format on  
the screen by selecting “Widescreen” or  
“Normal” under “Display Format” in the  
General Menu.  
Note:  
In some USB flash players (or memory  
devices), the stored contents are recorded  
using copyright protection technology. Such  
protected contents will be unplayable on any  
other devices (such as AJL308 device).  
Normal  
Wide screen  
File compatibility  
Music  
This device only supports unprotected music  
with the following file extension:  
.mp3  
Viewing video  
1
2
Repeat steps 1 to 3 in “Listening to music”.  
Press PHOTO/VIDEO to switch to  
VIDEO mode.  
Press 34 to select a video file.  
Press OK to play.  
To pause, press OK.To resume, press OK  
again.  
To display next/previous video file, press  
once or more 1 2.  
To fast forward/reverse, press and hold 2  
.wma  
Music bought from on-line music stores are  
not supported because they are secured by  
Digital Rights Management protection (DRM).  
3
4
Picture  
This device only supports picture file with the  
following file extension:  
.jpg  
or 1 until  
6
or  
5
appears on the lower-  
Video  
left corner of the screen, then press briefly  
and repeatedly to select 5 different playback  
speeds.To return to normal playback, press 2  
This device only supports video file with the  
following file:  
MPEG4  
or 1 until displayed  
6
or  
5
is change to 2.  
DivX  
To repeat One/All, press once or more 4.  
To cancel play mode, press 4 until “Off “is  
displayed.  
To switch between 16:9 and 4:3 screen  
ratio, press once or more 3.  
To select audio language, press and hold  
3 (The feature is dependent on video file.)  
To select subtitle language, press and  
hold 4 (The feature is dependent on video  
file.)  
Compatible USB device  
– USB flash memory (USB 2.0 or USB 1.1)  
– USB flash player (USB 2.0 or USB 1.1)  
USB device which requires driver installation  
under Windows XP is not supported.  
 
Sleep / Illumination  
Sleep  
Automatically adjusting  
To avoid strong light emitting from the unit at  
night time, the auto dim function can be used  
to adjust the brightness to the lowest level  
automatically.  
The clock radio has a built-in sleep timer,  
which enables the set to automatically turn  
off sound during radio or music playback  
after a set period of time.  
1
2
3
4
5
6
Press MENU.  
Option 1:  
Press TUNER.  
Press SLEEP until your desired sleep option  
is displayed.  
Radio will turn on if radio was previously  
turned off.  
Press 1 2 to highlight “General”.  
Press 34 to select “Auto DimTimer”.  
Press 1 2 to select “On”.  
Press 34 to select “Auto Dim - Start”.  
Press 1 2 to select the time that auto dim  
will start.  
1
2
7
8
Press 34 to select “Auto Dim - End”.  
Press 1 2 to select the time that auto dim  
will end.  
When auto dim is set, during auto dim time  
span, the LCD brightness will be auto  
adjusted to the lowest level. Press any  
button to increase the brightness and it will  
last 10 seconds.  
Option 2:  
Press CLOCK or PHOTO/VIDEO to  
enter respective mode.  
1
2
3
4
5
Press MENU.  
Press 1 2 to highlight “General”.  
Press 34 to select “SleepTimer Music”.  
Press 1 2 to select specific music you like.  
The set will turn on with the music you  
select.  
Using the stand  
Option 3: using USB/Memory card  
(SD/MMC)  
Repeat steps 1-8 described in “Listening to  
music”.  
Press SLEEP until your desired sleep option  
is displayed.  
The set is equipped with a stand on the  
bottom panel.To set the set for a different  
viewing angle take the stand out, then place it  
back by reversing (see the figure below) the  
side of the stand.  
1
2
To deactivate sleep function  
When sleep is activated,  
is display.  
Press SLEEP until “Offis displayed.  
Illumination brightness  
The LCD brightness can be adjusted  
manually and automatically.  
Manually adjusting  
Press REPEAT ALARM / BRIGHTNESS  
CONTROL once or more to cycle screen  
brightness through 4 levels.  
 
Setup menu  
Using Setup menu options  
The setup menu offers you advanced fea-  
tures.  
1
Press MENU.  
The menu appears.  
2
3
4
4
Press 1 2 to select “General”.  
Press 3 4 to select an item.  
Press 1 2 to select an option under the item.  
After finishing the setting, press CLOCK,  
TUNER, PHOTO/VIDEO or MUSIC to  
exit the setup menu.  
Setup  
Language  
Option  
Français Deutsch Español  
Description  
Select a desired on screen display  
language  
English/  
/
/
Brightness  
-3~3  
Select a brightness value  
Auto DimTimer  
Off/On  
Turns on or off auto dim for LCD  
brightness.  
Auto Dim - Start  
Auto Dim - End  
Wall Paper  
9: 00 PM  
7: 00 AM  
Set the start time for auto dim  
Set the end time for auto dim  
Blue/Green/Red/Purple  
Select different color for LCD  
background  
SleepTimer Music  
Picture Display  
3 music files are preset  
Select one file for sleep function  
Slideshow mode/Browse mode  
Sequential/Random  
Select different mode to display picture  
Select different slideshow sequence  
Slideshow Sequence  
*
Slideshow Effect  
None/Random /16 effects available Select different slideshow effects  
Select different slideshow intervals  
5 Seconds/10 Seconds/ 30 Seconds/  
1 Minute/ 5 Mintues/30 Minutes  
1/ Hour/ 2 Hours  
Slideshow Frequence  
Select picture display format  
Wide screen/Normal  
Display Format  
File Information Display Off/On  
Turns on or off file name display  
Video Display  
DivXVOD  
PlaybackTime/RemainTime  
Select different video time to be  
displayed  
Press OK to get DivX registration  
code.  
Press OK to restore to the factory  
default settings.  
Restore Default  
settings  
Reset  
* =To turn on slideshow effect, you must select slideshow mode in “Picture Display”.  
 
Safety and maintenance  
No objects filled with liquids, such as vases,  
shall be placed on the appartus.  
Safety and general  
maintenance  
No naked flame sources, such as lighted  
candles, should be placed on the apparatus.  
Do not cover the set. Adequate ventilation  
with a minimum gap of 6 inches between the  
ventilation holes and surrounding surfaces is  
necessary to prevent heat build-up.  
The mechanical parts of the set contain  
self-lubricating bearings and must not be  
oiled or lubricated.  
To clean the set, use a soft dry cloth. Do not  
use any cleaning agents containing alcohol,  
ammonia, benzene or abrasives as these may  
harm the housing.  
If you do not intend to use the clock radio  
for a long time, withdraw the power cord  
from the wall outlet.  
Place the set on a hard and flat surface so  
that the system does not tilt.  
Where the MAINS plug or an appliance  
coupler is used as the disconnect device, the  
disconnect device shall remain readily  
operable.  
Install the unit near the AC outlet and where  
the AC power plug can be easily reached.  
The apparatus shall not be exposed to drip-  
ping or splashing  
Do not expose the set, batteries, to humidity,  
rain, sand or excessive heat caused by  
heating equipment or direct sunlight.  
 
Troubleshooting  
If a fault occurs, first check the points listed below before taking the set for repair.  
If you are unable to remedy a problem by following these hints, consult your dealer or  
service center.  
WARNING: Do not open the set as there is a risk of electric shock. Under no  
circumstances should you try to repair the set yourself, as this will invalidate the  
warranty.  
No sound.  
The screen brightness keeps turning dark.  
– Volume not adjusted.  
• Adjust the VOLUME.  
– The set is in auto dim timing.  
To let the screen keep bright, turn off auto dim  
timer.  
Occasional crackling sound during FM  
broadcast.  
Note:  
When opening the folder of an external  
device or its file stored in, read time may  
exceed the normal time due to large  
folder or file.  
– Weak signal.  
• Extend the pigtail antenna fully.  
The alarm does not function.  
– Alarm time is not set.  
• See section on Setting and activating alarm.  
– Alarm is not activated.  
See section on Setting and activating alarm.  
“No card is selected” is displayed on the  
screen.  
– A USB device or memory card (SD or MMC) is  
not inserted.  
Insert a USB device or memory card (SD or  
MMC).  
 
INFORMATION REGARDING USB DIRECT:  
1. Compatibility of the USB connection on this product:  
a)This product supports most USB Mass storage devices (MSD) that these devices are compliant  
to the USB MSD standards.  
i) Most common Mass storage class devices are flash drives, memory sticks, jump drives and etc.  
ii) If you see a "Disc Drive" showing up on your computer after you have plugged the mass  
storage device into your computer, most likely it is MSD compliant and it will work with this  
product.  
b) If your Mass storage device requires a battery/power source, please make sure you have a  
fresh battery in it or charge the USB device first and then plug it into this product again.  
2. Supported Music type:  
a)This device only supports unprotected music with file extension: .mp3 .wma  
b) Music bought from on-line music stores are not supported because they are secured by  
Digital Rights Management protection (DRM).  
c) File name extensions that ended with the following are not supported: .wav; .m4a; .m4p; .mp4;  
.aac and etc.  
3. No Direct connection can be made from a Computer USB port to this product even you have  
either or both mp3 or wma file in your computer.  
Environmental information  
All unnecessary packaging material has been omitted.The packaging can be easily separat-  
ed into three materials: cardboard, polystyrene and plastic.  
Your set consists of materials which can be recycled if disassembled by a  
specialized company. Please observe the local regulations regarding the  
disposal of packaging, dead batteries and old equipment.  
 
Meet Philips at the Internet  
W
AJL308  
Printed in China  
PDCC-ZC-0811  
 

Peavey Microphone PVM 520TN User Manual
Peavey Speaker ED 100 User Manual
Philips Battery Charger DS 3000 User Manual
Pioneer DVD Player DV 210K K User Manual
Pioneer TV DVD Combo DVD V550 User Manual
Pitco Frialator Range L20 316 User Manual
Powermate Portable Generator PM052520203 User Manual
Pride Mobility Mobility Aid INFINFB2804 User Manual
Proctor Silex Slow Cooker 840149500 User Manual
PYLE Audio Car Stereo System PIFMDK6 User Manual