R
Please do not return product to retailer.
Por favor, no devuelva el producto al lugar de compra.
Veuillez ne pas retourner le produit au détaillant.
1--800--554--6723
Register your product online at:
Registre su producto en línea en:
Enregistrez votre produit en ligne à l’adresse :
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
PP2000T
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury. Refer
to your original manual for additional Warnings and Operating
Instructions.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves. Refiera a su manual original para las Instrucciones
de Funcioniamiento y las Advertencias adicionales.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves. Référez--vous à votre
manuel original pour des Avertissements et des Instructions d’Uti-
lisation additionnels.
Poulan PRO
7349 Statesville Road
Charlotte, NC 28269
545212825 Rev. 3 6/15/10 BRW
S Secure hair above shoulder length. Secure
or remove loose clothing or clothing with
loosely hanging ties, straps, tassels, etc.
They can be caught in moving parts.
S Being fully covered also helps protect you
from debris and pieces of toxic plants thrown
by spinning tines.
install the proper wall outlet. Do not change
the equipment plug, extension cord recep-
tacle, or extension cord plug in any way.
S To reduce risk of electrical shock, use exten-
sion cords specifically marked as suitable for
outdoor appliances having electrical rating not
less than the rating of unit. Cord must be
marked with suffix “W--A” (in Canada “W”).
Make sure your extension cord is in good
condition. Inspect extension cord before use
and replace if damaged. Do not use a dam-
aged cord. Cord insulation must be intact with
no cracks or deterioration. Plug connectors
must be undamaged. The extension cord
used to reach the power source must be
heavy enough to carry current from the power
source the full length of the extension cord to
the unit. An undersized extension cord will
cause a drop in line voltage resulting in loss of
power and overheating. If in doubt, use the
next heavier gauge. The lower the gauge
number, the heavier the cord.
S Stay alert. Do not operate when you are tired,
ill, upset, or under the influence of alcohol,
drugs, or medication. Watch what you are do-
ing; use common sense.
S Wear hearing protection.
S Never start or run inside a closed room or
building. Breathing exhaust fumes can kill.
S Keep handles free of oil and fuel.
S Never operate the cultivator without the tine
guard in place and properly secured.
FUEL SAFETY (for gas powerheads)
S Mix and pour fuel outdoors.
S Keep away from sparks or flames.
S Use a container approved for fuel.
S Do not smoke or allow smoking near fuel or
the powerhead.
S Do not use multiple cords.
S Do not abuse cord. Never carry the unit by the
extension cord or yank extension cord to dis-
connect unit. To unplug, grasp the plug, not
the cord. Do not use cord as a handle, close a
door on cord, or pull cord around sharp edges
or corners. Do not expose cords to heat, oil,
or water.
S Avoid spilling fuel or oil. Wipe up all fuel spills
before starting the powerhead.
S Move at least 10 feet (3 meters) away from
fueling site before starting powerhead engine.
S Stop engine and allow to cool before remov-
ing fuel cap.
S Remove fuel cap slowly.
S Keep the extension cord clear of operator and
obstacles at all times.
S Store unit and fuel in an area where fuel va-
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
S Tie cord to cord retainer and connect to re-
cessed plug as shown in this manual to pre-
vent damage to unit and/or extension cord
and to reduce the possibility of the extension
cord disconnecting from the unit during op-
eration.
ELECTRICAL SAFETY (for electric
powerheads)
S Do not attempt to repair unit. Inspect the insu-
lation and connectors on the powerhead and
extension cord before each use. If there is
any damage, do not use until damage is re-
paired by your authorized service dealer.
S Do not use the powerhead if the switch does
not turn the unit on and off properly. Have the
unit repaired by your authorized service deal-
er.
S Do not use with damaged cord or plug. If pow-
erhead is not working as it should, has been
dropped, damaged, left outdoors, or dropped
into water, return it to your authorized service
dealer for repair.
S Avoid unintentional starting of the unit. Never
carry unit with your finger on the switch. Be
sure the switch is in the OFF position and
never touch the switch when connecting ex-
tension cord.
S Unplug the unit from the power source when
not in use, before servicing, and when chang-
ing accessories and/or attachments.
S Avoid any body contact with any grounded
conductor, such as metal fences, or pipes, to
avoid the possibility of electric shock.
S Ground Fault Circuit Interrupter (GFCI)
protection should be provided on the circuit or
outlet to be used for the powerhead. Recep-
tacles are available having built-in GFCI
protection and may be used for this measure
of safety.
WARNING: Avoid a dangerous envi-
ronment. To reduce the risk of electrical shock,
do not use in rain, in damp or wet locations, or
around swimming pools, hot tubs, etc. Do not
expose to snow, rain, or water to avoid the pos-
sibility of electrical shock. Do not use on wet
surfaces. Do not handle extension cord plug or
unit with wet hands.
S Use only a voltage supply as shown on the
nameplate of the unit.
S Avoid dangerous situations. Do not use in
presence of flammable liquids or gases to
avoid creating a fire or explosion and/or caus-
ing damage to unit.
S Avoid dangerous environments. Do not use in
unventilated areas or where dust or explosive
vapors can build up.
S To reduce the risk of electric shock, the pow-
erhead may have a polarized plug (one blade
is wider than the other); if so, it will require the
use of a polarized extension cord. The ap-
pliance plug will fit into a polarized extension
cord only one way. If the plug does not fit fully
into the extension cord, reverse the plug. If
the plug still does not fit, obtain a correct polar-
ized extension cord. A polarized extension
cord will require the use of a polarized wall
outlet. This plug will fit into the polarized wall
outlet only one way. If plug does not fit fully
into the wall outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to
3
S Hold the unit firmly with both hands.
S Keep firm footing and balance. Do not over-
reach or stand on unstable surfaces.
S Look behind and use care when backing up.
S Keep all parts of your body away from the
tines and muffler.
UNIT/MAINTENANCE SAFETY
WARNING: Disconnect powerhead
spark plug (or disconnect powerhead from pow-
er source) before performing maintenance.
S Inspect entire unit before each use. Replace
damaged parts. Check for fuel leaks. Make
sure all fasteners are in place and securely
fastened.
S Maintain unit according to recommended pro-
cedures.
S Have all maintenance and service not ex-
plained in this manual performed by an autho-
rized service center.
S Do not force the unit. Use only for jobs ex-
plained in this manual. Use only for cultivating.
Do not abuse unit. Do not use in rain or wet
locations.
S Use only in daylight or good artificial light.
TRANSPORTING AND STORAGE
S Stop powerhead before leaving work area.
S Allow powerhead and gearbox to cool before
storing or transporting it in a vehicle.
S Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
S Store attachment so tines cannot accidentally
cause injury.
S Store attachment indoors, out of reach of chil-
dren.
S Throw away tines that are bent, warped,
cracked, broken, or damaged in any other
way. Replace parts that are cracked, chipped,
or damaged before using the unit.
S Use only recommended Poulan PRO parts
and accessories. Never use wire, wire rope,
string, flailing devices, etc.
S Be sure tines stop turning when engine idles
(see CARBURETOR ADJUSTMENTS sec-
tion of powerhead manual).
If situations occur which are not covered in
this manual, use care and good judgment. If
you need assistance, call 1-800-554-6723.
S Remove the tines before making carburetor
adjustments. Hold the unit by hand.
S Keep others away when making carburetor
adjustments.
SPECIAL NOTICE: Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swellings. Prolonged use in cold
weather has beenlinked to blood vesseldam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti-vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this unit.
S Never start the unit with the clutch housing re-
moved. The clutch can fly off and cause seri-
ous injury.
S Avoid heavy contact with solid objects that
might stop the tines. If heavy contact occurs,
stop the unit and inspect for damage.
S If tines strike a foreign object, follow these
steps: stop unit and disconnect spark plug
wire (or disconnect from power source), in-
spect for damage, and repair any damage be-
fore resuming operation of the unit.
S Never douse or squirt the attachment with
water or any other liquid. Clean unit and de-
cals with a damp sponge (see STORAGE).
CULTIVATING SAFETY
WARNING: Inspect the area to be
cultivated before each use. Remove objects
(rocks, vines, branches, broken glass, nails,
wire, string, etc.) which can be thrown by the
tines or can wrap around the shaft.
SAVE THESE INSTRUCTIONS
4
OPERATION
KNOW YOUR CULTIVATOR ATTACHMENT
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
CULTIVATOR ATTACHMENT. Compare the illustrations with your attachment to familiarize yourself
with the location of the various controls and adjustments. Save this manual for future reference.
Hanger
Cutting Tines
CUTTING TINES
TINE GUARD
The CUTTING TINES are designed to loosen
soil.
The TINE GUARD provides partial protection
from the rotating tines.
NOTE: The cutting tines can not be turned
by hand due to the gear ratio.
OPERATING THE COUPLER
Coup
Your powerhead is equipped with a coupler
which enables optional attachments to be
installed. The optional attachments are:
MODEL:
Edger . . . . . . . . . . . . . . . . . . . . . . . PP1000E
Blower . . . . . . . . . . . . . . . . . . . . . . PP3000B
Pruner . . . . . . . . . . . . . . . . . . . . . . PP5000P
Pruner . . . . . . . . . . . . . . . . . . . . . . PP5500P
Brushcutter* . . . . . . . . . . . . . . . . . PP4000C
*not designed for use with electric powerheads
Attachment
SEN
Knob
TIGHTEN
WARNING: Always disconnect pow-
erhead spark plug (or disconnect powerhead
frompower source) beforeremoving or instal-
ling attachments.
2. Press and hold the locking/release button.
Locking/Release
Button
REMOVING ATTACHMENT
CAUTION: When removing or installing at-
tachments, place the powerhead and attach-
ment on a flat surface for stability.
1. Loosen the coupler by turning the knob
counterclockwise.
Upper Shaft
Attachment
Coupler
3. While securely holding the upper shaft,
pull the attachment straight out of the cou-
pler.
5
INSTALLING ATTACHMENT
1. Remove the shaft capfrom theattachment
(if present) and discard.
WARNING: To avoid personal injury,
never carry the cultivator while the unit is run-
ning.
2. Position locking/release button of attach-
ment into guide recess of upper shaft cou-
pler.
WARNING: The gearbox gets very
hot after extended periods of use. To avoid
burns, do not touch the gearbox until it has
been allowed to cool.
3. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
4. Before using the unit, tighten the knob se-
CULTIVATING
curely by turning clockwise.
1. Move the cultivator to the work area prior to
starting the engine/motor.
Primary Hole
Coupler
Guide Recess
2. With the engine/motor running and the
tines off the ground, press the throttle trig-
ger to increase the engine speed.
3. Hold trigger handle and assist handle firm-
ly. Slowly lower the cultivator until thetines
make contact with the ground.
Locking/
Release
Button
Upper
Shaft
Attachment
WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit. Using the wrong hole could
lead to serious injury or damage to the unit.
Locking/Release
Button in Primary Hole
4. As unit begins cultivating, pull back on the
unit so that the tines can penetrate the
ground.
INSTALLING ATTACHMENT
HANGER
An attachment hanger is provided for storage
when attachment is not in use.
To install hanger on attachment:
1. Remove the shaft capfrom theattachment
(if present) and discard.
2. Press and hold the locking/release button.
3. Push hanger onto the attachment until the
locking/release button snaps into the hole.
OPERATING POSITION
ALWAYS WEA
Eye Protection
5. Once the ground has been broken, contin-
ueat a moderatepace until you are familiar
with the controls and the handling of the
cultivator.
Long Pan
6. Pull the cultivator backwards to improve
the depth of cultivation andreduce your ef-
fort.
Heavy Sho
7. To cultivate in confined areas or narrow
rows, remove the left and right outer tines
(see TINE REPLACEMENT).
6
MAINTENANCE
TINE MAINTENANCE
WARNING: Always stop unit anddis-
connect spark plug wire (or disconnect pow-
erheadfrompower source) before performing
maintenance.
WARNING: The tines will continue to
spin after the engine stops or after the throttle
trigger has been released. To avoid serious
injury, make sure the tines have stopped
coasting and disconnect the spark plug (or
disconnect powerhead from power source)
before performing work on the tines.
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service center for re-
placement of damaged or worn parts.
S Tine Guard -- Discontinue useof cultivator if
tine guard is damaged.
WARNING: Always replace tines
that are bent, warped, cracked, broken, or
damaged in any other way. Never attempt to
straighten and reuse a damaged tine. Use
only specified replacement tines. Wear pro-
tective gloves when handling or performing
maintenance on the tines to help avoid injury.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Clevis pins
S Hitch pin clips
INSPECT AND CLEAN UNIT AND
DECALS
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
decals using a damp cloth with a milddeter-
gent.
S Wipe off unit with a clean dry cloth.
SERVICE AND ADJUSTMENTS
2. Remove the tines and felt cushions from
the shaft.
TINE REPLACEMENT
3. Clean and oil the shaft.
WARNING: The tines will continue to
spin after the engine stops or after the throttle
trigger has been released. To avoid serious
injury, make sure the tines have stopped
coasting and disconnect the spark plug (or
disconnect powerhead from power source)
before performing work on the tines.
4. Replace the tines and the felt cushions.
WARNING: Wear protective gloves
when handling or performing maintenance on
the tines to avoid injury. The tines become very
sharp from use.
1. Remove the hitch pin clips and clevis pins.
5. Repeat previous steps on opposite side.
6. Reinstall clevis pins and hitch pin clips.
NOTE: When installed correctly, the hubs
on the tines will face each other. The letters
“R” stamped on the tines will be on the right
side of the cultivator and the letters “L” will be
on the left side.
Clevi
7
STORAGE
S Clean the entire attachment.
WARNING: Perform the following
steps after each use:
S Inspect the tine guard area and clean any
dirt or debris that has collected. Inspect the
tines; replace tines that are bent, warped,
cracked, broken or damaged in any other
way.
S Allow attachment and gearbox to cool be-
fore storing or transporting.
S Position attachment so that any sharp ob-
ject cannot accidentally cause injury.
S Store the attachment in a dry, well venti-
lated area out of the reach of children.
S Lightly oil external metal surfaces.
S Check entire attachment for loose screws
or nuts. Replace any damaged, worn or
broken parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasolineto
oil ratio.
SEASONAL STORAGE
Prepare attachment for storage at end of sea-
son or if it will not be used for 30 days or more.
If your cultivator attachment is to be stored for
a period of time:
LIMITED WARRANTY
Poulan PRO, a division of Husqvarna Con-
sumer Outdoor Products N.A., Inc., warrants
to the original consumer purchaser that each
new Poulan PRO brand gasoline tool or at-
tachment is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline
product or attachment as follows from the
original date of purchase.
In Canada, contact:
Poulan PRO
850 Matheson Blvd. West
Mississauga,Ontario L5V 0B4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE OTH-
ER RIGHTS WHICH VARY FROM STATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIM-
ITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson--Moss Act
of 1975.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or alteration, or
the use of accessories and/or attachments not
specifically recommended by Poulan PRO for
this tool. This warranty does not cover parts that
will wear and require replacement with reason-
able use during the warranty period. This war-
ranty does not cover pre--delivery setup or nor-
mal adjustments explained in the instruction
manual. This warranty does not cover trans-
portation costs.
The policy of Poulan PRO is to continuously
improve its products. Therefore, Poulan
PRO reserves the right to change, modify, or
discontinue models, designs, specifications,
and accessories of all products at any time
without notice or obligation to any purchaser.
In the event you have a claim under this warran-
ty, you must return the product to an authorized
service dealer.
Should you have any unanswered questions
concerning this warranty, please contact:
Poulan PRO, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
7349 Statesville Road
Charlotte, NC 28269
1--800--554--6723
8
|